Thermal interface material

From Wikipedia, the free encyclopedia

A thermal interface material (shortened to TIM) is any material that is inserted between two components in order to enhance the thermal coupling between them. A common use is heat dissipation, in which the TIM is inserted between a heat-producing device (e.g. an integrated circuit) and a heat-dissipating device (e.g. a heat sink). There are intensive studies in developing several kinds of TIM with different target applications:

  • Thermal paste: Mostly used in the electronics industry, thermal pastes provide a very thin bond line and therefore a very small thermal resistance. They have no mechanical strength (other than the surface tension of the paste and the resulting adhesive effect) and require an external mechanical fixation mechanism. Because they do not cure, thermal pastes are typically only used where the material can be contained, or in thin applications where the viscosity of the paste will allow it to stay in position during use.
  • Thermal adhesive: As with thermal pastes, thermal adhesives provide a very thin bond line, but provide additional mechanical strength to the bond after curing. While curing TIMs like thermal adhesives may be used outside of a semiconductor package, often they are used in inside of a thermal package, as their curing properties can improve reliability over different thermal stresses.[1] Thermal adhesives come in both single-part formulations as well as two-part formulations, often containing additives to improve thermal conductivity, including solid fillers (metal oxides, carbon black, carbon nanotubes, etc.)[2], or liquid metal droplets.[3]
  • Thermal gap filler: This could be described as "curing thermal paste" or "non-adhesive thermal glue". It provides thicker bond lines than the thermal paste, as it cures while still allowing an easy disassembly, thanks to limited adhesiveness.
  • Thermally conductive pad: As opposed to previous TIMs that come in a fluidic form, thermal pads are manufactured and used in a solid state (albeit often soft). Mostly made of silicone or silicone-like material, thermal pads have the advantage of being easy to apply. They provide thicker bond lines (ranging in thickness from larger than a few hundred µm to a few mm) to accommodate non-flat interfaces and even multi-component interfaces, but will usually need higher force to press the heat sink onto the heat source, so that the thermal pad conforms to the bonded surfaces.
  • Thermal tape: These materials adhere to the bonded surfaces, require no curing time, they are easy to apply. Similar to thermal pads, they are typically shipped in a solid but flexible form and come in a variety of thicknesses larger than a few hundred µm.
  • Phase-change materials (PCM): Naturally sticky materials, used in place of thermal pastes. Its application is similar to solid pads. After achieving a melting point of 55–60 degrees, it changes to a half-liquid status and fills all gaps between the heat source and the heat sink.
  • Metal thermal interface materials (metal TIMs): Metallic materials offer substantially higher bulk thermal conductivity as well as the lowest thermal interface resistance. This high conductivity translates to less sensitivity to bondline thicknesses and coplanarity issues than polymeric TIMs.[4] Common metals used as TIMs include the relatively soft and compliant indium alloys, as well as sintered silver.

See also[edit]

References[edit]

  1. ^ Kearney, Andrew; Li, Li; Sanford, Sean (2009). "Interaction between TIM1 and TIM2 for mechanical robustness of integrated heat spreader". 2009 25th Annual IEEE Semiconductor Thermal Measurement and Management Symposium. pp. 293–298. doi:10.1109/STHERM.2009.4810778. ISBN 978-1-4244-3664-4. S2CID 29501079.
  2. ^ Liu, Johan; Michel, Bruno; Rencz, Marta; Tantolin, Christian; Sarno, Claude; Miessner, Ralf; Schuett, Klaus-Volker; Tang, Xinhe; Demoustier, Sebastien (2008). "Recent progress of thermal interface material research - an overview". 2008 14th International Workshop on Thermal Inveatigation of ICs and Systems. pp. 156–162. doi:10.1109/THERMINIC.2008.4669900. ISBN 978-1-4244-3365-0. S2CID 40595787. Retrieved 30 March 2023.
  3. ^ Bartlett, Michael; Kazem, Navid; Powell-Palm, MAtthew; Huang, Xiaonan; Sun, Wenhuan; Malen, Jonathan; Majidi, Carmel (2017). "High thermal conductivity in soft elastomers with elongated liquid metal inclusions". Proceedings of the National Academy of Sciences. 114 (9): 2143–2148. Bibcode:2017PNAS..114.2143B. doi:10.1073/pnas.1616377114. PMC 5338550. PMID 28193902.
  4. ^ Jarrtett, Robert N.; Ross, Jordan P.; Berntson, Ross (September 2007). "Full Metal TIMs". Power Systems Design Europe.