Double data rate
In computing, double data rate (DDR) describes a computer bus that transfers data on both the rising and falling edges of the clock signal and hence doubles the memory bandwidth by transferring data twice per clock cycle.[1][2][3] This is also known as double pumped, dual-pumped, and double transition. The term toggle mode is used in the context of NAND flash memory.
Overview[edit]
The simplest way to design a clocked electronic circuit is to make it perform one transfer per full cycle (rise and fall) of a clock signal. This, however, requires that the clock signal changes twice per transfer, while the data lines change at most once per transfer. When operating at a high bandwidth, signal integrity limitations constrain the clock frequency.[citation needed] By using both edges of the clock, the data signals operate with the same limiting frequency, thereby doubling the data transmission rate.
This technique has been used for microprocessor front-side busses, Ultra-3 SCSI, expansion buses (AGP, PCI-X[4]), graphics memory (GDDR), main memory (both RDRAM and DDR1 through DDR5), and the HyperTransport bus on AMD's Athlon 64 processors. It is more recently being used for other systems with high data transfer speed requirements – as an example, for the output of analog-to-digital converters (ADCs).[5]
DDR should not be confused with dual channel, in which each memory channel accesses two RAM modules simultaneously. The two technologies are independent of each other and many motherboards use both, by using DDR memory in a dual channel configuration.
An alternative to double or quad pumping is to make the link self-clocking. This tactic was chosen by InfiniBand and PCI Express.
Relation of bandwidth and frequency[edit]
Describing the bandwidth of a double-pumped bus can be confusing. Each clock edge is referred to as a beat, with two beats (one upbeat and one downbeat) per cycle. Technically, the hertz is a unit of cycles per second, but many people refer to the number of transfers per second. Careful usage generally talks about "500 MHz, double data rate" or "1000 MT/s", but many refer casually to a "1000 MHz bus," even though no signal cycles faster than 500 MHz.
DDR SDRAM popularized the technique of referring to the bus bandwidth in megabytes per second, the product of the transfer rate and the bus width in bytes. DDR SDRAM operating with a 100 MHz clock is called DDR-200 (after its 200 MT/s data transfer rate), and a 64-bit (8-byte) wide DIMM operated at that data rate is called PC-1600, after its 1600 MB/s peak (theoretical) bandwidth. Likewise, 12.8 GB/s transfer rate DDR3-1600 is called PC3-12800.
Some examples of popular designations of DDR modules:
| Names | Memory clock | I/O bus clock | Transfer rate | Theoretical bandwidth |
|---|---|---|---|---|
| DDR-200, PC-1600 | 100 MHz | 100 MHz | 200 MT/s | 1.6 GB/s |
| DDR-400, PC-3200 | 200 MHz | 200 MHz | 400 MT/s | 3.2 GB/s |
| DDR2-800, PC2-6400 | 200 MHz | 400 MHz | 800 MT/s | 6.4 GB/s |
| DDR3-1600, PC3-12800 | 200 MHz | 800 MHz | 1600 MT/s | 12.8 GB/s |
| DDR4-2400, PC4-19200 | 300 MHz | 1200 MHz | 2400 MT/s | 19.2 GB/s |
| DDR4-3200, PC4-25600 | 400 MHz | 1600 MHz | 3200 MT/s | 25.6 GB/s |
| DDR5-4800, PC5-38400 | 300 MHz | 2400 MHz | 4800 MT/s | 38.4 GB/s |
| DDR5-6400, PC5-51200 | 400 MHz | 3200 MHz | 6400 MT/s | 51.2 GB/s |
DDR SDRAM uses double-data-rate signalling only on the data lines. Address and control signals are still sent to the DRAM once per clock cycle (to be precise, on the rising edge of the clock), and timing parameters such as CAS latency are specified in clock cycles. Some less common DRAM interfaces, notably LPDDR2, GDDR5 and XDR DRAM, send commands and addresses using double data rate. DDR5 uses two 7-bit double data rate command/address buses to each DIMM, where a registered clock driver chip converts to a 14-bit SDR bus to each memory chip.
See also[edit]
- DDR SDRAM, DDR2 SDRAM, DDR3 SDRAM, DDR4 SDRAM and DDR5 SDRAM
- GDDR SDRAM, GDDR3 SDRAM, GDDR4 SDRAM, GDDR5 SDRAM and GDDR6 SDRAM
- List of interface bit rates
- Pumping (computer systems)
- Quad data rate
References[edit]
- ^ Hennessy, John L.; Patterson, David A. (2007). Computer architecture: a quantitative approach. Amsterdam: Morgan Kaufmann. p. 314. ISBN 978-0-12-370490-0.
- ^ Harris, Sarah L.; Harris, David Money (2016). "I/O Systems: 9.6.3 DDR3 Memory". Digital Design and Computer Architecture. Elsevier. p. 531.e1–531.e64. doi:10.1016/b978-0-12-800056-4.00015-7. ISBN 978-0-12-800056-4.
DRAM connects to the microprocessor over a parallel bus. In 2015, the present standard is DDR3, a third generation of double-data rate memory bus operating at 1.5 V. Typical motherboards now come with two DDR3 channels so they can simultaneously access two banks of memory modules. DDR4 is ... operating at 1.2V ...
- ^ "double data rate (DDR) Definition". Intel. Retrieved 2024-04-07.
- ^ Schmid, Patrick. "PCI Express Battles PCI-X". Tom's Hardware Guide.
- ^ "AD9467 ADC" (PDF) (data sheet). Analog Devices.